It is currently Sun May 19, 2013 8:36 am

View unanswered posts | View active topics


Board index » Autodesk Inventor Discussion » Autodesk Inventor Discussion

All times are UTC





Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Previous topic | Next topic 
Author Message
iDS!
PostPosted: Thu Aug 25, 2011 5:36 pm 
Offline
MCAD Guru
User avatar

Joined: 07 Jun 2005
Posts: 2546
Country: United States
State: Florida
CAD System: Inventor
Ok guys...anyone have this issue before with iLogic?

Setting up a new install for the new CAD guy and upon updating this particular system to IV2011 the attached error appears at start-up...hit ok and IV continues to load...

...so I tried repair install, reloaded IV, and now I've used the Uninstall Tool for IV2011 http://usa.autodesk.com/adsk/servlet/ps ... ID=9242018
...worked like a charm btw (kudos to ADSK!) ...took less than 30min...and wiped EVERYTHING adsk clean!

So went about installing fresh...then chk'd ...no luck same issue, then chk'd after booth sp...no luck...but I get a small error now? ...see 1st attachment


You do not have the required permissions to view the files attached to this post. You must LOGIN or REGISTER to view these files.

_________________
Steve Robbins
Inventor Design Solutions & Innovations
"I believe in being an innovator " - Walt Disney
@_iDSi


Share on FacebookShare on TwitterShare on DiggShare on DeliciousShare on TumblrShare on Google+
Top
 Profile  
 
iDS!
PostPosted: Thu Aug 25, 2011 5:40 pm 
Offline
MCAD Guru
User avatar

Joined: 07 Jun 2005
Posts: 2546
Country: United States
State: Florida
CAD System: Inventor
...ok so I guess restarting IV 3 times was the charm? ...seems fine...however I need to test some iLogic :D

_________________
Steve Robbins
Inventor Design Solutions & Innovations
"I believe in being an innovator " - Walt Disney
@_iDSi
Top
 Profile  
 
jpek42
PostPosted: Thu Aug 25, 2011 6:33 pm 
Offline
MCAD Lurker

Joined: 19 Feb 2010
Posts: 1
Country: United States
State: Michigan
CAD System: Inventor
Try deleting the file (with the really long path name) that's called out in the 2nd dialog you posted.
Jeff
Top
 Profile  
 
iDS!
PostPosted: Thu Aug 25, 2011 7:39 pm 
Offline
MCAD Guru
User avatar

Joined: 07 Jun 2005
Posts: 2546
Country: United States
State: Florida
CAD System: Inventor
thanks Jeff...looks like that worked as well...have rebooted and no issues so far :D

_________________
Steve Robbins
Inventor Design Solutions & Innovations
"I believe in being an innovator " - Walt Disney
@_iDSi
Top
 Profile  
 
iDS!
PostPosted: Fri Aug 26, 2011 1:35 pm 
Offline
MCAD Guru
User avatar

Joined: 07 Jun 2005
Posts: 2546
Country: United States
State: Florida
CAD System: Inventor
FYI...here's the solution ADSK DSG had...

http://beinginventive.typepad.com/being ... -2011.html

...yeah go figure its the wonderful Ribbon again!

_________________
Steve Robbins
Inventor Design Solutions & Innovations
"I believe in being an innovator " - Walt Disney
@_iDSi
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Autodesk Inventor Discussion » Autodesk Inventor Discussion

All times are UTC


Who is online

Users browsing this forum: No registered users and 3 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
POWERED_BY